Gear Pump
Hydraulics
运行在线示例
免费 · 无需注册 · 直接在浏览器中运行
齿轮泵是位于端口 A(吸油)与 B(压油)之间的容积泵。轴每转一圈都从 A 向 B 输送一个排量,与压力无关;压力升高时有少量内泄漏。
轴是普通信号:把转速接到 ω(例如直流电机的转速),再把泵的转矩输出接回该电机的负载转矩。泵在压力下工作时电机就会减速。未接信号时,泵按其 speed 参数运行。
实际工程类比: 代表由电机驱动的外齿轮泵,为工业液压站或行走机械提供定排量高压油液源。
数学模型
Q = rac{V_d,omega}{2pi} - G,Delta p, qquad T = rac{V_d,Delta p}{2pi,eta_m}
其中:
Vd为排量 (m³/转),ω为轴转速 (rad/s)Δp = p_B − p_A为升压 (Pa)G = (1 − η_v)·Vd·ω_nom / (2π·Δp_nom)为泄漏导纳,由样本效率确定η_m在泵送时除理想转矩,泵被反向驱动作马达时乘以理想转矩
输入与输出
| Direction | ID | Label | 类型 | Status |
|---|---|---|---|---|
| → In | p |
A (in) | number | Required |
| → In | n |
B (out) | number | Required |
| → In | flange |
Shaft | number | Optional |
| → In | in |
ω | number | Optional |
| → In | H |
H | number | Optional |
| ← Out | torque |
T | number | Output |
| ← Out | flow |
Q | number | Output |
参数
| 参数 | Label | 类型 | 默认值 | 描述 |
|---|---|---|---|---|
displacement |
Displacement | number | 0.00001 |
Volume per revolution; 1e-5 m³ is 10 cm³/rev |
volumetric_efficiency |
Volumetric efficiency | number | 0.95 |
Delivered over ideal flow at nominal speed and pressure; sets the internal leakage |
mechanical_efficiency |
Mechanical efficiency | number | 0.9 |
Ideal over shaft torque while pumping |
nominal_speed |
Nominal speed | number | 157.08 |
Speed at which the volumetric efficiency is rated; 157.08 rad/s is 1500 rpm |
nominal_pressure |
Nominal pressure | number | 10000000 |
Pressure rise at which the volumetric efficiency is rated |
speed |
Speed | number | 157.08 |
Shaft speed while the ω input is not wired |
flow_ripple |
Gear-tooth flow ripple | boolean | false |
When enabled, models periodic flow pulsation at the tooth-meshing frequency (z · ω); disable for an ideal smooth pump |
teeth_count |
Teeth per gear | number | 8 |
Number of teeth on each pump gear; sets both the visual gears and the flow-ripple frequency |
gear_profile |
Gear profile | select | spur |
Spur involute gears produce sharper handover dips and higher ripple; helical gears mesh gradually with ~65% less ripple |
ripple_amplitude |
Ripple amplitude override | number | 0 |
0 = automatic from teeth count and gear profile (~1/z²); set > 0 to override with a custom fractional amplitude |
使用示例
直流电机驱动泵
示例 examples/basic-gearpump.json:24 V 直流电机驱动 2 cm³/转的泵,经 0.5 mm 阀门供油,并有 25 bar 溢流阀通往油箱。出口压力稳定在约 18 bar,转速约 29 rad/s。t = 3 s 时阀门关至 20%:压力升至溢流阀,泵转矩增大,电机减速。请用 TR-BDF2 运行。
说明与最佳实践
- 务必给流量留出路。容积泵面对关闭的阀会无限升压;请在出口与油箱之间接一个 Relief Valve。
- 轴耦合:转矩输出接到电机的负载转矩输入。转速和转矩以信号传递,而非机械端口。
- 表压:所有液压压力均相对于环境;开口油箱为 0 Pa。
- 单位:压力用 Pa(1 bar = 100 000 Pa),流量用 m³/s(1 L/min ≈ 1.667e-5 m³/s)。